Mustek PP7000-II Uživatelská příručka

Aura Series (PP7000 / PP7000-II) Thermal Printer User's Guide Rev.: A1 IMPORTANT!!!! Please read carefully before usin

H. USEFUL TIPS • Do not touch the areas around the print head and motor during or right after printing. It can be very hot. • Do not use thermal pa

II. QUICK START-UP A. LOADING PAPER 1. Desk top application 1. Slide the hood lock toward the front of the printer to release the hood. 2. R

2. When to replace paper Whenever the printer gives paper out signal or a red line appears on the thermal paper, it is the proper timing for replacin

window the switch positions both 1, and 2 to ON leaving the rest unchanged as factory default setting. 3. Peripheral connection The peripheral contro

sure that the type of power cord and the voltage requirement of the power adaptor meet the local power conditions. Now the printer is ready for power

moment, a font table will be printed in text mode again. To exit the test printing, please turn the printer off and on again. C. SPECIAL ADJUSTMENTS

extremely light bobbin, easily causing the paper roll to go off position when paper feeding with low remaining paper. In this case, the paper near en

III. MAINTENANCE GUIDES A. MAINTENANCE GUIDE LINES • Always turn off and disconnect power before opening the cover. • The areas around the print he

Before putting back the paper roll for printing, alcohol solvent must be dried completely. D. TROUBLE SHOOTING This section gives solutions to some p

If there is no paper jam and the print head is not overheated, turn off the printer and wait for half a minute then turn it back on. If the problem s

Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Cla

speed by adjusting an internal switch describe in last chapter of the manual. 3. Paper Jam Problems Paper is jammed inside the printer – Turn off the

it back to position when finish. The lock up of the print hood can then be released after this problem solved. Please use manual cutter as temporary

IV. SPECIFICATIONS A. PRINTER ITEM SPECIFICATION Printing method Thermal sensitive line dot method Effective printing width 64 mm Thermal head con

C. POWER ADAPTOR ITEM REQUIREMENT INPUT VOLTAGE 100 V AC ~ 250 V AC INPUT FREQUENCY 50 ~ 60 HZ INPUT CURRENT 1.5 A MAX. @ 115 V AC OUTPUT VOLTAGE

V. TECHNICAL INFORMATION A. INTERFACES 1. Peripheral interface The connector for peripheral control is a 6P6C RJ11 jack with the following pin assign

B. SETUP WINDOW On bottom cover of the Aura series thermal printer, there is screwed a metal plate for setup window. In this window, there is a 8 pos

Switch position 4 defines the handshaking method in serial interface. When it is set to ON, the printer transmits an “XOFF” for busy and sends an “XO

C. INTERNAL SWITCH There is an extra internal 4 position DIP switch in PP7000-II for more technical settings. To access these setup, please first tur

D. SOFTWARE COMMANDS The Aura thermal printer supports all commands applicable to Epson printer TM-T88II. The only difference is the smoothening comm

Table Of Contents GETTING STARTED . . . . . . . . . . . . . . . . . . . . . 1 -- 1 CONGRATULATION . . . . . . . . . . . . . . . . . . . . . . 1 --

ESC ‘p’ m n1 n2: Kitchen bell drive command (m = ‘0’, 0 ≦ n1 ≦ n2 ≦ 255) Hexadecimal codes are: 1B 70 m n1 n2 This command can be used to drive a kit

E. CHARACTER CODE PAGES Aura series printer supports all code pages and international character sets applicable to Epson printer TM-T88. They are: Pa

PRINT HEAD CLEANING . . . . . . . . . . . . . . . . . 3 -- 1 TROUBLE SHOOTING . . . . . . . . . . . . . . . . . . . . 3 -- 2 General problems .

I. GETTING STARTED A. CONGRATULATION You have made a very wise decision by purchasing the easy loading ; low noise ; high resolution ; light weight

reminder function to persons around. It can be used to drive a separately purchased kitchen bell for such reminder function in noisy environment. Thi

a Power adaptor + power cord (depend on country type ordered). b Power supply cable (when no power adaptor ordered) This printer power supply cable i

Front View Rear View Parallel Connector Power Switch Serial Connector Power Connector Peripheral Connector Frame Ground Botto

G. OPERATING ENVIRONMENT • Place the printer on a sturdy, level surface. • Choose a place that is well ventilated and free of excessive dust, smoke